PARTS CLEANING SYSTEM

Are you wasting valuable man hours?

  

Simply load the machine, set the timer & walk away
 The Apollo Spray Wash uses it's own tank of hot water, bio-degradable detergent & inhibitor with the combination of a revolving
basket & high pressure jets providing an economical environmentally friendly alternative to the drudgery of hand cleaning
1400 High Top -  1 tonne load  -  1400mm gear drive basket turntable
The 1400 Hi-Top is also designed to clean trailer dual wheel & brake drum assemblies as one unit. Additional spray bar fitting is added to clean the centres.





 

 Maximum cleaning efficiency
Uses only hot water & detergent
Low running costs
Electric wash cycle timer
Electric motor driven turntable
Auto water level top up
7 day clock for heating elements
Easy to clean tank with auto pump out
Environmentally friendly

Excellence in design and quality.
Easily the best value washer on the market today,
combined with full after sales service.
Don't settle for anything less!

 How much skilled workshop time is spent hand cleaning parts each day!
You may well be wasting valuable resources.


Spray jets on the 1400 Hi-Top

APOLLO SW1400 HI-TOP SPECIFICATIONS


Rear of machine showing pump & pump out facility

Basket Diameter 1400mm
Job Weight (Maximum) 1000kg
Spray Bar Height 760mm
Loading Lip Height 950mm
Water Tank Capacity 300 Litres
Power Requirement 32 amp - 3 Phase
Pump (350 Litre/min) 5.5 kW 3 Phase
Pump Pressure 425 kpa (60 psi)
Water Heaters (Temp) 3 x 3.6kW (80oC)
Machine Height 1460mm
Machine Width 1830mm
Machine Depth (length) 1990mm
Machine Weight 550kg
  • The basket turntable is gear driven at 5 rpm, eliminating dangerous over speeding experienced with large water drive turntables. 40% more water is available for cleaning as water is no longer required to dive the basket turntable.
  • The basket rotates on a heavy duty slab axle using tapered roller bearings.
  • One-piece closed loop fixed spray bar design gives maximum cleaning efficiency. The spray bar has no joints or hoses to fail. Spray bar has a flushing valve to allow simple cleaning of any spray hole blockages. 2 x 3mm wash jets are used.
  • Easy clean 300L chemical tank has two lids for full access. Large capacity, easy clean gasket & particle strainers lift out with tank lids. Strainers have smaller holes than the spray bar to minimise blockages.
  • Insulated tank & lid ensures high efficiency & low running costs.
    A one-piece lid labyrinth seal area does not require a gasket or latch. There are no welded metal joints to rust. Gas strut assisted lid allows one handed operation. A safety switch shuts off the pump when lid is lifted.
  • Electronic wash timer optimises the cleaning cycle time & reduces power costs.
  • Auto water level control with mains connection (also provides heating element protection). Water temp is thermostat controlled at 80oC & connected to a 7 day timer.
  • Auto pump out feature allows water to be pumped out in minutes for periodic machine tank cleaning.
  • Heavy duty Australian made pump is located so that the pump seal can be serviced without removal of motor. Pump overload protection fitted.
  • Long life industrial two pack painted finish minimises paint flaking & rusting.
    Small parts container for nuts & bolts, etc


Control Panel

Australasian Machinery Dealer Services Pty Ltd (A.M.D.S.)
 A.C.N. 111 546 082
PO Box 1050, Wagga Wagga NSW 2650
Contact: Chris Smith
Ph: 02 6921 2011     (+ 61 2 6921 2011)
Website www.amds.com.au  or  www.spraywash.com.au  Email: office@amds.com.au

Please note: Due to ongoing developments specifications may change.

PRINTABLE BROCHURE  -  CLICK HERE

   

 Home

 Go Back